How to attach polycarbonate to a greenhouse: 3 installation features
If you decide to fix polycarbonate on the greenhouse yourself, then you should familiarize yourself with the correct sequence of work in advance. When arranging greenhouses, polycarbonate is widely used, fixing it on a pre-prepared frame. The result is a structure that is strong, reliable and durable. In addition, this design is characterized in that it is capable of transmitting light in the required amount. When creating a polycarbonate greenhouse, you must definitely know how to properly fix the sheets, as this will avoid many mistakes and complete the installation work successfully. When creating a greenhouse, cellular or monolithic polycarbonate is used. Monolithic polycarbonate sheets are a translucent sheet material that resembles glass, but is much lighter and stronger.
How to cut polycarbonate for a greenhouse
Polycarbonate is a colorless, moderately dense polymer-type plastic. To carry out the installation of a polycarbonate greenhouse, you need to cut and cut polycarbonate sheets.
In order to cut polycarbonate sheets, you need to prepare tools such as:
- Stationery durable knife;
- Hacksaw for wood;
- Hand saw.
Before you fix the polycarbonate, you first need to cut it correctly
When cutting, it is important that the protective film on the polycarbonate sheets remains intact. The resulting sawdust in the joints must be periodically blown off with compressed air.
Carbon should be cut in such a way that there is as little waste as possible. To do this, you need to first prepare a drawing on paper, considering several different cutting options and then choosing the most economical way for yourself.
It is much more convenient to cut along the voids of polycarbonate, as this will prevent breakage of the material. Often, polycarbonate greenhouses are created exactly of the arched type, so the cutting of sheets must be carried out in stages, starting from the roof. With a tape measure, you must initially measure the size of the arc, draw it with a marker and cut the prepared roll. Then you need to cut out two rectangles for the doors and only after that proceed with the preparation and cutting of the side parts.
The ends of all parts of the prepared material must be closed with a special sealing tape. During the installation, it is imperative to place polycarbonate sheets outward on the side that has a protective layer, as this will protect the greenhouse from negative ultraviolet radiation.
Which side to lay polycarbonate on the greenhouse
Sheet polycarbonate is lightweight and transmits light very well, which is why it is widely used and is used for arranging greenhouses. In order for the greenhouse design to be strong and reliable, it is imperative to take into account the basic rules for installing polycarbonate sheets and know which side to put the material on the prepared frame in order to ensure good plant growth. Polycarbonate can be very different, it all depends on the characteristics of the top layer of this material.
For arranging a greenhouse, it is better to choose polycarbonate with good reflectivity
In particular, the types of polycarbonate sheets differ in their coating, which can be:
- Infrared reflective coating;
- Partially transmissive to ultraviolet rays;
- Honeycomb polycarbonate with good reflectivity.
The most popular material for greenhouses is polycarbonate with a special coating that transmits part of the infrared spectrum, while retaining harmful radiation. It is very important to put such polycarbonate correctly, because otherwise, the climate inside the greenhouse will be detrimental to plants, and the material itself will very quickly fall into poor condition and begin to collapse.
Important! In order to correctly position the polycarbonate sheets during installation, you need to pay attention to the feature of the protective coating. The top is often patterned or marked.
With the correct installation of polycarbonate sheets, the finished structure will last for a long time.
Mounting polycarbonate on a greenhouse: installation features
Polycarbonate is considered an excellent material for the construction of greenhouses and greenhouses.
Many people prefer to choose polycarbonate because it is practical and easy to install
This material is valued among buyers due to:
- Low cost;
- Ease of installation;
- Usability.
When arranging a polycarbonate greenhouse, you need to know how to properly attach the sheets to the frame so as not to damage the fragile material. Polycarbonate laying requires special care and accuracy, which is why fastening is carried out using special self-tapping screws or screws with thermal washers.
Thermal washers are special seals with which you can attach polycarbonate sheets to a frame made of any material. Such seals guarantee high bond strength.
Thermal washers provide good protection against the penetration of cold air, as well as high tightness at the attachment points. This design prevents the penetration of atmospheric precipitation and condensate. This device is very easy to use, the most important thing is to properly lay polycarbonate sheets so that the greenhouse will last for a long time.
Connecting polycarbonate to each other in a greenhouse
Polycarbonate is considered a fairly good universal building material, which is widely used for greenhouse construction.
You can connect polycarbonate using special glue or profile joints
This material has excellent qualities, in particular it is excellent:
- Soundproofing;
- Heat insulation;
- Water resistant.
Before installing polycarbonate sheets on the greenhouse, you must first carry out all the required calculations, as well as markings. In addition, it must be taken into account that the connection of individual polycarbonate sheets to each other has certain specifics. You can fasten the sheets together using special profile joints or glue.
The calculation of the required number of fasteners is carried out depending on the available dimensions of the surface plane made of polycarbonate. In addition, all bends and corner joints must be taken into account. Very easy to use and install profile connections. To make the connection of polycarbonate sheets not too noticeable, a special glue is used to glue the individual parts.
Silicon-based adhesive is used for stronger bonding, providing a super strong bond.
The greenhouse made of polycarbonate is highly durable and reliable. But in order for the structure to serve for a long time, it is necessary to carry out the correct installation, taking into account all the requirements.
By the way, did you know what can expand the possibilities of your polycarbonate greenhouse? It doesn t matter if you bought a polycarbonate greenhouse kit or built it yourself. For the correct and convenient operation of your greenhouse, you can buy additional high-quality greenhouse accessories here! This will make the growing process more comfortable and you will be able to provide your plants in the greenhouse with the right conditions for growth.